From the Service Handbook, kindly supplied by Mike Knapman.
SPRINGS
Passenger & Commercial
Transverse type front and rear springs are used on all passenger and commercial cars. On all models 1935 to 1941 inclusive, the front spring is mounted ahead of the front axle and the rear spring mounted back of the rear axle. This provides a longer “spring base” than the wheelbase of the car. One of the major advantages of transverse springs is the reduction in unsprung weight.
Trucks
Transverse type front springs were used on all trucks 1934 to 1939 inclusive with the exception of 1939 C.O.E. models. On these latter models, and on all later model trucks two longitudinal front springs of the semi-elliptic type are used.
The use of this type of spring facilitates servicing of the engine since it simplifies removal of the engine oil pan, makes the crank case more readily accessible and thereby reduces the time required to perform such service operations.
Rear springs of all truck models are the semi-elliptic type mounted lengthwise of the chassis on the outside of the frame side members.
Auxiliary springs when used on the heavier model trucks provide reserve capacity for heavy loads. This makes it possible to have sufficient flexibility in the main rear springs to produce good riding qualities of the unit when lighter loads are carried.
Lubrication
The transverse type front and rear spring assemblies as used on all passenger and commercial cars are designed to permit pressure lubrication. Illustration “A” shows in detail the lubricant grooves provided in the spring leaves while illustration “B” shows the length of the grooves in the various leaves which ensure lubrication of the entire length of each spring leaf. Illustration “C” shows the course of the lubricant through the lubricator fitting, the slots in the tie bolt nut and spring leaves and then along the grooves in the leaves.
This is the direct opposite of the conventional method of spraying springs on the outer edges of the leaves and is one of the major features contributing to the riding quality of the springs.
The specifications of M-4628-B Ford spring lubricant were adopted to ensure thorough lubrication and maximum spring efficiency. The talcum in the lubricant prevents the oil from being forced out between the leaves and act as an anti-friction medium. As tests and experiments have proven conclusively that M-4628-B Ford spring lubricant is most suitable, it is essential that only this lubricant or its equivalent, purchased from reputable suppliers, be used for lubricating these springs. Other types of lubricants are unsuitable, will not provide correct lubrication and will in all probability considerably reduce the spring efficiency.
All springs used on all truck models are lubricated by spraying with penetrating oil. It is advisable to ensure thorough lubrication, to periodically remove the weight of the body and chassis from the springs (by lifting front or rear of the body with a hoist), which will permit easier penetration of the lubricant between the leaves.
Spring shackle studs used on all passenger and commercial cars are of the oilless type and require no lubrication, while those used on most truck models are provided with lubricator fittings.
Spring Covers
Both front and rear springs on 1940 Deluxe, 1941 Super Deluxe, and Mercury passenger cars are equipped with metal covers for better retention of spring lubricant and to keep out water and dust. They thus assist in maintaining the ease and smoothness of spring action.
Clutch
Engines in all cars and trucks are equipped with semi-centrifugal type single plate clutches. These clutches are noted for their exceptional ability to stand up in hard service, also for their easy pedal action.
The centrifugal force principle is utilized to supplement the pressure exerted by the clutch springs and clamp the clutch disc more tightly between the pressure plate and the rear face of the flywheel. Thus the torque or power transmitting capacity of the clutch is far in excess of the maximum engine torque. The additional pressure which is automatically applied as the engine speed is increased, not only prevents the clutch from slipping when delivering full engine torque, but reduces the amount of slippage during clutch engagement. This minimizes wear on the clutch disc facings and increases their life.
Because pressure on the clutch plate is automatically increased the pressure of the clutch springs is relatively low.
This makes it possible to have easy pedal action. The clutch pedal can be depressed with little effort at gear shifting speeds.
Friction in release lever action is reduced by mounting the levers on the pressure plate with needle roller bearings. Flywheel and pressure plate surfaces which come into contact with clutch facings are extremely smooth and finished to minimize facing wear. Spring steel segments between the clutch disc and the rear facing help to cushion the engaging action. This prevents grabbing and ensures smooth starting.
Clutch pilot bearings and release bearings are of the pre-lubricated type to provide long service and low maintenance.
The clutch has three release levers with weighted outer end. Each lever is mounted on the pressure plate with needle roller bearings. Levers are also attached to clutch cover by pin and roller pivot type bearing. As engine speed increased centrifugal force causes the weighted end of the lever to attempt to assume a position in the vertical plane and they move forward, exerting increased pressure against the clutch plate. There are nine clutch pressure plate springs. In all cars and trucks the clutch housing and transmission case are cast integral. This assures correct alignment at all times of the clutch and transmission with the engine.
Adjustment
The clutch pedal travel adjustment must be maintained at all times. The amount of movement can easily be determined by moving the clutch pedal down with a slight hand pressure.
The travel will gradually lessen as the mileage on the vehicle increases owing to normal wear. Driving with the foot resting on the clutch pedal will result in clutch slippage and premature wear, also necessitating more frequent adjustment. Adjustment is made through decreasing the length of the clutch pedal adjusting rod as necessary to provide correct free travel of the clutch pedal.